A passerby observed a male struggling with a female so they stopped to assist her. On June 22, 2021, at 6:54 am, Officers were dispatched to 2300 Armstrong in reference to a domestic disturbance with an assault in progress. Gonzales was not located at the time of the incident. The victim was transported to a local hospital by ambulance and is in stable condition. Officers rendered first aid to the victim until medics arrived on scene. The suspect fled the scene prior to Officers' arrival. A 31 year old male had been stabbed multiple times by the suspect. Gonzales followed them to the Stripes on Glenna, where the stabbing occurred.Īt 9:09 pm, Officers were dispatched to the Stripes located at 901 Glenna in reference to a stabbing that had just occurred. She was driven away from that location by a friend in attempt to get away from the suspect.
![izzys game time brick rigs izzys game time brick rigs](https://i.ytimg.com/vi/cO79YMr3nqg/mqdefault.jpg)
On June 21, 2021, an altercation occurred at the 400 blk of E Harris between Jerry Gonzales (8-9-00) and his ex-girlfriend. The identity of the second victim is being withheld at this time pending notification of the family.
#IZZYS GAME TIME BRICK RIGS DRIVER#
The driver of the Kia Sportage was identified as Raphael Salas (45) from Del Rio. They were pronounced deceased by Judge Howard. The driver of the Honda Accord was not wearing a seatbelt.ĭue to the impact, the driver of the Kia Sportage and the driver of the Honda Accord succumbed to their injuries at the scene. The Honda Accord then veered off the road and struck a large sign. After further investigation it was discovered that the driver of the Kia Sportage ran onto Loop 306 and was struck by the Honda Accord. The Kia Sportage had struck multiple large rocks at the front of the school and came to a stop.Ī second wrecked vehicle (White Honda Accord) was located at 600 W Houston Harte. When Officers arrived on scene they located a disabled vehicle (Red Kia Sportage) in the parking lot of Central High School (655 Caddo). On August 2, 2021, at 1:29 am, Officers were dispatched to a major motor vehicle accident. One of the three occupants had been wearing a seatbelt.Īccording to witnesses, the driver of the Chevrolet Tahoe was travelling east at the 1400 block of Edmund when it suddenly swerved into the westbound lane, striking the Chevrolet Silverado 2500. Three occupants of the Chevrolet Silverado 2500 received treatment but had non-incapacitating injuries. The other three occupants of the Chevrolet Tahoe had non-incapacitating injuries. He was pronounced deceased by Judge Howard. The front passenger of the Chevrolet Tahoe, Jermaine Landor (33), succumbed to his injuries at the hospital. The adults in the vehicle were not wearing seatbelts but the children were. Both vehicles had extensive damage.Īll four occupants of the Chevrolet Tahoe (Two adults and two children, ages 8 and 11) were transported by ambulance to a local hospital.
![izzys game time brick rigs izzys game time brick rigs](https://i.ytimg.com/vi/AceErLt_990/hqdefault.jpg)
Two vehicles (Black Chevrolet Tahoe and a White Chevrolet Silverado 2500) had been involved in a head on collision. The notch has been removed in the side view to allow for a forstner (or similar) bit to have clearance.On August 3, 2021, at 7:50 pm, Officers were dispatched to the 1400 block of Edmund in regards to a Major Motor Vehicle Accident. Then run the bottom plane of the jig through a table saw (or whatever you have that will work) to shave an angled wedge from the bottom. You can make the jig as above to get a perfectly square reference. It is possible to make this jig with the vertex at a different angle. To allow for a forstner bit, cut a section from the bottom of the jig (see the side view image) allowing just enough clearance for the bit. You may need to make several of these to accommodate different sized bits. Place the jig flat against the surface you want to drill, snug the drill bit up to the inner corner (the cut out area), and drill away. From the end of the stock, cut a wedge section that is 90° in the wedge (the left inner face should be 90° from the right inner face) and the wedge vertex (the line in the middle of the removed area), should also be 90° from the bottom face of the block.
![izzys game time brick rigs izzys game time brick rigs](https://img.youtube.com/vi/ceVZ1HHuMLw/hqdefault.jpg)
I saw a video online, that suggested a simple jig that will allow you to drill straight into a relatively flat surface.